Ubuntu
snapd package

Browsing Filipino translation

  1. Mantic (23.10)
  2. Template “snappy”
  3. Filipino (fil)
Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions.

These translations are shared with snapd trunk series template snappy.

13 → 22 of 925 results First • • • Last
13.

The check-snapshot command verifies the user, system and configuration
data of the snaps included in the specified snapshot.

The check operation runs the same data integrity verification that is
performed when a snapshot is restored.

By default, this command checks all the data in a snapshot.
Alternatively, you can specify the data of which snaps to check, or
for which users, or a combination of these.

If a snap is included in a check-snapshot operation, excluding its
system and configuration data from the check is not currently
possible. This restriction may be lifted in the future.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_snapshot.go:76
14.

The confinement command will print the confinement mode (strict,
partial or none) the system operates in.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_confinement.go:31
15.

The connect command connects a plug to a slot.
It may be called in the following ways:

$ snap connect <snap>:<plug> <snap>:<slot>

Connects the provided plug to the given slot.

$ snap connect <snap>:<plug> <snap>

Connects the specific plug to the only slot in the provided snap that matches
the connected interface. If more than one potential slot exists, the command
fails.

$ snap connect <snap>:<plug>

Connects the provided plug to the slot in the core snap with a name matching
the plug name.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_connect.go:37
16.

The connections command lists connections between plugs and slots
in the system.

Unless <snap> is provided, the listing is for connected plugs and
slots for all snaps in the system. In this mode, pass --all to also
list unconnected plugs and slots.

$ snap connections <snap>

Lists connected and unconnected plugs and slots for the specified
snap.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_connections.go:42
17.

The console-conf-start command starts synchronization with console-conf

This command is used by console-conf when it starts up. It delays refreshes if
there are none currently ongoing, and exits with a specific error code if there
are ongoing refreshes which console-conf should wait for before prompting the
user to begin configuring the device.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_routine_console_conf.go:40
18.

The create-cohort command creates a set of cohort keys for a given set of snaps.

A cohort is a view or snapshot of a snap's "channel map" at a given point in
time that fixes the set of revisions for the snap given other constraints
(e.g. channel or architecture). The cohort is then identified by an opaque
per-snap key that works across systems. Installations or refreshes of the snap
using a given cohort key would use a fixed revision for up to 90 days, after
which a new set of revisions would be fixed under that same cohort key and a
new 90 days window started.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_create_cohort.go:30
19.

The create-key command creates a cryptographic key pair that can be
used for signing assertions.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_create_key.go:41
20.

The create-user command creates a local system user with the username and SSH
keys registered on the store account identified by the provided email address.

An account can be setup at https://login.ubuntu.com.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_create_user.go:33
21.

The debug command contains a selection of additional sub-commands.

Debug commands can be removed without notice and may not work on
non-development systems.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_debug.go:29
22.

The delete-key command deletes the local cryptographic key pair with
the given name.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_delete_key.go:41
13 → 22 of 925 results First • • • Last

This translation is managed by Ubuntu Team Philippines, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

No-one has contributed to this translation yet.